Hello & Welcome to our community. Is this your first visit? Register

User Tag List

Thanks Thanks:  2
Likes Likes:  3
Dislikes Dislikes:  0
Results 1 to 5 of 5
  1. #1
    Junior Member
    Bike
    2016 MT09, ZX7R, Deauville
    Join Date
    Feb 2018
    Location
    Bristol, UK
    Posts
    7
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    MT09 common mod feedback

    Hey all,

    In light of it being quiet here I thought I would add a short post to review a few things I have done to my 2016 MT09. It might help others decide what to do themselves!


    Ok so first off:

    K-tech Razor R rear shock / Ktech 20IDS fork cartridges with KTech springs.(9.8cst oil in comp leg, 15.9cst in reb leg)

    * Rear shock feels excellent and far more controlled than the standard shock, fully adjustable for comp, reb, shock length and preload. Stock shock would pogo stick around over bumps, this does not. Highly reccomended.

    * Forks feel rather harsh (compression) even with most of the compression dialed out. It is sport bike stiff, but the bike does handle rather well now, brake dive is eliminated and it is a maassive improvement over the stock setup.

    Given the choice again I would do both without hesitation.

    MT09 common mod feedback-img_20180729_141456-jpg MT09 common mod feedback-img_20180729_141451-jpg

    MT09 2013-2016 Comfort seat

    I find this a marked improvement over the stock seat, I only paid 70 so I am happy with it for that, though I hear the 2017 comfort seat is far better. Being a short arse though this is perfect as it doesn't add any ride height to the seat from the stock item. Stock seat would cause my butt to ache after 20mins or so, this doesn't have this issue.



    Yamaha heated grips

    Fitted these at the weekend, official Yamaha heated grips, they connect directly to the battery and have an auto shut off feature. I ran the main wire along the left side of the bike, along the throttle cables under the tank (just loosen the tank to tuck this under and zip tie), it then runs under the front plastic shroud that fits to the tank.
    The left grip cable I ran the along the clutch cable and connected it to the main wire under the top yoke along side the left fork. The cable to connect to the right grip I ran behind the dash.
    The right grip wire I ran along the switchgear wire and then behind the dash and connected to the left cable.

    First thoughts today are that they feel warm quickly on the hottest setting (with summer gloves), it took about 25mins before I felt the need to turn them down a notch. They are only 22W max power draw though so I imagine they will be no where near as hot as a set of Oxford grips on full whack (48W, 4A draw).

    But they look great, they look oem.

    MT09 common mod feedback-img-20181013-wa0005-jpg MT09 common mod feedback-img-20181013-wa0007-jpg

    Chinese Savage screen

    Cheap chinese OEM copy screen, looks identical, close up the quality is a little lacking, unpolished cut edges for example, but for 16, who cares.



    Puig touring screen


    Fair bit higher than the standard size screen, looks great side on, looks terrible head on! Riding wise it does push a fair bit of air out of the way, makes long distance far more tolerable at speed!
    MT09 common mod feedback-img_20180731_234536-jpg


    R+G tail tidy

    This was on the bike when I bought it, it looks good, but it leaves a smalll hole in the undertray uncovered that allows dirt to get inside. I will be putting my stock rear end on when I get 5mins, so if anyone wants an R+G tail tidy let me know.



    I've also shod the bike with some Michelin PR5's they are working rather well.


    Last thing I want to do is to fit a decent exhaust, I did buy a Lextek XP8C from Simmiperformance on ebay, it arrived and looked good but I had several issues with it which were down to build quality. I was looked after by Simmiperformance throughout and they refunded me fully. Lextek admitted that they allowed a batch of under par systems to hit the shelves, I was unlucky it seems. So I am still on the lookout for something decent without having to pay 700+ for a carbon Akra.

    Anyway, maybe that could be of help to someone!

    Cheers
    Mike
    Last edited by bacon; 10-17-2018 at 05:11 PM.

  2. #2
    Senior Member stevecbr's Avatar
    Bike
    Yamaha MT09 & Xmax 250
    Join Date
    Oct 2013
    Location
    Norwich, Norfolk, United Kingdom
    Posts
    926
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)
    Never realised they sold cheap screens on Ebay, just checked and they look good

  3. #3
    Senior Member fizzy's Avatar
    Bike
    MT09SP MT10SP Honda cb 360
    Join Date
    Jun 2014
    Location
    Darlington
    Posts
    459
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)
    Nice write up on your mods Bacon, I got one of the copy screens for my bike (2018 sp)23 delivered identical to the puig screen and good quality saving over 70 quid
    I now see they doing ones the same as the yamaha ones for under 30 quid bargain!

  4. #4
    Junior Member woodie100's Avatar
    Bike
    MT09 Tracer 16
    Join Date
    Oct 2018
    Location
    Swansea
    Posts
    26
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by bacon View Post
    Hey all,

    In light of it being quiet here I thought I would add a short post to review a few things I have done to my 2016 MT09. It might help others decide what to do themselves!


    Ok so first off:

    K-tech Razor R rear shock / Ktech 20IDS fork cartridges with KTech springs.(9.8cst oil in comp leg, 15.9cst in reb leg)

    * Rear shock feels excellent and far more controlled than the standard shock, fully adjustable for comp, reb, shock length and preload. Stock shock would pogo stick around over bumps, this does not. Highly reccomended.

    * Forks feel rather harsh (compression) even with most of the compression dialed out. It is sport bike stiff, but the bike does handle rather well now, brake dive is eliminated and it is a maassive improvement over the stock setup.

    Given the choice again I would do both without hesitation.

    MT09 common mod feedback-img_20180729_141456-jpg MT09 common mod feedback-img_20180729_141451-jpg

    MT09 2013-2016 Comfort seat

    I find this a marked improvement over the stock seat, I only paid 70 so I am happy with it for that, though I hear the 2017 comfort seat is far better. Being a short arse though this is perfect as it doesn't add any ride height to the seat from the stock item. Stock seat would cause my butt to ache after 20mins or so, this doesn't have this issue.



    Yamaha heated grips

    Fitted these at the weekend, official Yamaha heated grips, they connect directly to the battery and have an auto shut off feature. I ran the main wire along the left side of the bike, along the throttle cables under the tank (just loosen the tank to tuck this under and zip tie), it then runs under the front plastic shroud that fits to the tank.
    The left grip cable I ran the along the clutch cable and connected it to the main wire under the top yoke along side the left fork. The cable to connect to the right grip I ran behind the dash.
    The right grip wire I ran along the switchgear wire and then behind the dash and connected to the left cable.

    First thoughts today are that they feel warm quickly on the hottest setting (with summer gloves), it took about 25mins before I felt the need to turn them down a notch. They are only 22W max power draw though so I imagine they will be no where near as hot as a set of Oxford grips on full whack (48W, 4A draw).

    But they look great, they look oem.

    MT09 common mod feedback-img-20181013-wa0005-jpg MT09 common mod feedback-img-20181013-wa0007-jpg

    Chinese Savage screen

    Cheap chinese OEM copy screen, looks identical, close up the quality is a little lacking, unpolished cut edges for example, but for 16, who cares.



    Puig touring screen


    Fair bit higher than the standard size screen, looks great side on, looks terrible head on! Riding wise it does push a fair bit of air out of the way, makes long distance far more tolerable at speed!
    MT09 common mod feedback-img_20180731_234536-jpg


    R+G tail tidy

    This was on the bike when I bought it, it looks good, but it leaves a smalll hole in the undertray uncovered that allows dirt to get inside. I will be putting my stock rear end on when I get 5mins, so if anyone wants an R+G tail tidy let me know.



    I've also shod the bike with some Michelin PR5's they are working rather well.


    Last thing I want to do is to fit a decent exhaust, I did buy a Lextek XP8C from Simmiperformance on ebay, it arrived and looked good but I had several issues with it which were down to build quality. I was looked after by Simmiperformance throughout and they refunded me fully. Lextek admitted that they allowed a batch of under par systems to hit the shelves, I was unlucky it seems. So I am still on the lookout for something decent without having to pay 700+ for a carbon Akra.

    Anyway, maybe that could be of help to someone!

    Cheers
    Mike
    What are the DRL s ? They look nice too! You added them on? If so how and where from?

    JonB

  5. #5
    Member
    Bike
    2016 MT09
    Join Date
    Apr 2018
    Location
    Bristol
    Posts
    39
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    I don't have any DRLs fitted

 

 

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
All times are GMT -7. The time now is 11:46 PM.
Powered by vBulletin® Version 4.2.5
Copyright © 2018 vBulletin Solutions Inc. All rights reserved.
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Feedback Buttons provided by Advanced Post Thanks / Like v3.6.3 (Lite) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Original Poster In Postbit provided by Original Poster In Postbit v1.0.0 (Free) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.


MT09.motorcycle-talk.com is not associated with Yamaha in any way. We are an enthusiast site dedicated to the Yamaha MT-09 / FZ-09 motorcycles. Our goal is to offer a place for Yamaha FZ09 / MT09 owners to discuss rides, events, mods, maintenance, purchasing, etc.

vBulletin Skin By: PurevB.com